Page 1 of 1
3par size not matching
Posted: Wed Feb 09, 2022 3:27 am
by Phill
Hello
I am new on san if you can help me, I have 3par virtual size 520G, reserved used user space 413G, used user size 78%, and in bare-metal rhel server show 430G, why not show 520G in bare-metal?
Re: 3par size not matching
Posted: Wed Feb 09, 2022 4:36 am
by MammaGutt
Phill wrote:Hello
I am new on san if you can help me, I have 3par virtual size 520G, reserved used user space 413G, used user size 78%, and in bare-metal rhel server show 430G, why not show 520G in bare-metal?
Not sure where you're seing each number or what you're actually looking at. Could you provide some outputs or screenshots of the different numbers?
Re: 3par size not matching
Posted: Wed Feb 09, 2022 4:44 am
by Phill
you can see in screenshot the virtual size 520G, reserved used user space 413G, but in my bare-metal server show 430G, my question is I need to increase my bare-metal space, so how i can make server see remaining space up to 520G ?
Re: 3par size not matching
Posted: Wed Feb 09, 2022 5:17 am
by MammaGutt
Phill wrote:you can see in screenshot the virtual size 520G, reserved used user space 413G, but in my bare-metal server show 430G, my question is I need to increase my bare-metal space, so how i can make server see remaining space up to 520G ?
3PAR is block storage. The entire volume is presented to the host.
Are you seing 430G as device size or partition size?
edit: I think "lsblk" will give you some info in RHEL.
Re: 3par size not matching
Posted: Wed Feb 09, 2022 5:26 am
by Phill
Yes you can see down on bare-metal server, this is version 5 not support lsblk
Code: Select all
PV VG Fmt Attr PSize PFree
/dev/mpath/............3731 vgu06 lvm2 a-- 430.00G 0
another question why virtual size 520G different than reserved used user space 413G?
Re: 3par size not matching
Posted: Wed Feb 09, 2022 5:35 am
by MammaGutt
Phill wrote:Yes you can see down on bare-metal server, this is version 5 not support lsblk
Code: Select all
PV VG Fmt Attr PSize PFree
/dev/mpath/............3731 vgu06 lvm2 a-- 430.00G 0
another question why virtual size 520G different than reserved used user space 413G?
Your volume is Thin (provisioned).
Virtual size = volume size
Reserved size = The actual amout of data stored on the volume.
All I see from your output is partition size... not device size. My guess there is free/unpartitioned space on the device not used in RHEL.
Re: 3par size not matching
Posted: Wed Feb 09, 2022 6:05 am
by Phill
Code: Select all
fdisk -l /dev/mpath/............3731
Disk /dev/mpath/............3731: 558.3 GB, 558345748480 bytes
255 heads, 63 sectors/track, 67881 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mpath/............3731 doesn't contain a valid partition table
you can see it show 558GB which is different than what assigned in 3par, 520G why?
Re: 3par size not matching
Posted: Wed Feb 09, 2022 6:10 am
by MammaGutt
Phill wrote:Code: Select all
fdisk -l /dev/mpath/............3731
Disk /dev/mpath/............3731: 558.3 GB, 558345748480 bytes
255 heads, 63 sectors/track, 67881 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mpath/............3731 doesn't contain a valid partition table
you can see it show 558GB which is different than what assigned in 3par, why?
GiB/GB discussion.
520 * 1024 * 1024 * 1024 * 1024 = 558 345 748 480 Bytes.
520 GiB = 558.3 GB
Re: 3par size not matching
Posted: Wed Feb 09, 2022 6:21 am
by Phill
thanks , so my issue now from host side only, but SAN fine,
do you know how i add remaining space up to 580G to VG with 430G