has anyone had success getting the web interface for SSMC 3.1 to run on port 443? we are using the linux version and followed the steps on page 17 of the admin guide here:
http://h20566.www2.hpe.com/hpsc/doc/pub ... 06232en_us
but the web interface doesn't come back up after a service start (on 443 or 8443)
SSMC Customer Feedback
Re: SSMC Customer Feedback
SSMC 3.1 it would be interesting to be able to compare two systems with a scheduled report in the same way as can be done for on-demand reports. Once the report is created and scheduled, the comparison selection is not respected. Thanks
Re: SSMC Customer Feedback
Right, and this will be changed in SSMC 3.2 so the other system will be displayed in the scheduled report too.SergioQC wrote:Once the report is created and scheduled, the comparison selection is not respected.
Re: SSMC Customer Feedback
I just found that SSMC 3.2 has been posted to HPE's Software Updates portal and available for download. As of this writing, though, SSMC 3.1 is still listed as the version available via Software Depot.
Re: SSMC Customer Feedback
This week we updated our Lab InServ from 3.2.2 to 3.3.1 EGA
Before update we completely cleaned up the array.
After 3.3.1, I setup vvol's again for testing and moved a VM to the 3PAR.
Before the update, SSMC showed the VM's which were provisioned with vvols on the Container
But now after the upgrade and vmotion, Storage Container in SSMC say's it conains 2(?) VM's, but when click on it, no VM's are shown.
It also say's it contains 5 vvols, however after clicking on it ... nothing.
However from the CLI:
Doing a showvolsc it shows the container containing 2 VM's en 5 vvols
Doing a showvolvm -sc <container_name> it show the VM I moved containing 4 vvols.
I already created a new Storage Container and vmotioned the VM to it: still the same.
I also noticed that the state for both containers say's: Unknown
Just installed 3.2 in our Lab, still the same issue with the Containers and VM's
Before update we completely cleaned up the array.
After 3.3.1, I setup vvol's again for testing and moved a VM to the 3PAR.
Before the update, SSMC showed the VM's which were provisioned with vvols on the Container
But now after the upgrade and vmotion, Storage Container in SSMC say's it conains 2(?) VM's, but when click on it, no VM's are shown.
It also say's it contains 5 vvols, however after clicking on it ... nothing.
However from the CLI:
Doing a showvolsc it shows the container containing 2 VM's en 5 vvols
Doing a showvolvm -sc <container_name> it show the VM I moved containing 4 vvols.
I already created a new Storage Container and vmotioned the VM to it: still the same.
I also noticed that the state for both containers say's: Unknown
Just installed 3.2 in our Lab, still the same issue with the Containers and VM's
Re: SSMC Customer Feedback
That doesn't sound right. If you could, please open a support case so they can collect the logs and we can get this figured out.mkaaden wrote:But now after the upgrade and vmotion, Storage Container in SSMC say's it conains 2(?) VM's, but when click on it, no VM's are shown.
It also say's it contains 5 vvols, however after clicking on it ... nothing.
Re: SSMC Customer Feedback
Hi Brian,
This 3PAR is out of support, hence we performed the upgrade to 3.3.1
Is it still possible then to open a case on a Inserv that has no Support ?
Does it make any difference whether we de a compleet reinstall of SSMC before we contact support at all ?
Regards,
Martijn
This 3PAR is out of support, hence we performed the upgrade to 3.3.1
Is it still possible then to open a case on a Inserv that has no Support ?
Does it make any difference whether we de a compleet reinstall of SSMC before we contact support at all ?
Regards,
Martijn
Re: SSMC Customer Feedback
It shouldn't matter but it's worth a try. I'll follow up with you in a PM to see what we can do to find out what's causing SSMC to not display the VVOL info.mkaaden wrote:Does it make any difference whether we de a compleet reinstall of SSMC before we contact support at all ?
Re: SSMC Customer Feedback
Have seen an Issue on 4 Systems (at 2 Sites) after Update to 3.3.1.
On all 3PARs after the Update the SSMC 3.2 shows "0 Ports" in Systems.
Remove and add the Arrays in SSMC fix it.
@wbbouldin
Have you try to remove and add the Storage?
May be it fix it for you to.
On all 3PARs after the Update the SSMC 3.2 shows "0 Ports" in Systems.
Remove and add the Arrays in SSMC fix it.
@wbbouldin
Have you try to remove and add the Storage?
May be it fix it for you to.
Re: SSMC Customer Feedback
Just to make sure I understand the order of events, you updated SSMC to version 3.2 and then updated the 3PAR OS to 3.3.1, right? From what version of the 3PAR OS did you update?cali wrote:On all 3PARs after the Update the SSMC 3.2 shows "0 Ports" in Systems.
Remove and add the Arrays in SSMC fix it.