HPE Storage Users Group

A Storage Administrator Community




Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: Receive Error count on management interfaces
PostPosted: Thu Jan 02, 2014 12:14 pm 
User avatar

Joined: Fri Jun 21, 2013 1:03 pm
Posts: 113
Location: USA
I've an an on-again off-again revolving ticket issue with HP support over the last few months. The below error message appears across varying management interfaces on a 7400 and on a 7200. It seems as if HP support is stumped by the issue, thoughts?

State : New
Message Code: 0x0260001
Repeat Count: Occurred 6 times, first at 2013-12-18 19:26:13 CST
Time : 2013-12-27 01:23:28 CST
Severity : Informational
Type : Ethernet Monitor Event
Component : hw_node:0,hw_eth:0
Message : Node 0 eth0 Ethernet device error detected- Receive Error count increased by (2) (200%)- Receive Frame Error count increased by (2) (200%)

Id : 76
State : New
Message Code: 0x0260001
Repeat Count: Occurred 19 times, first at 2013-12-20 06:33:10 CST
Time : 2013-12-26 04:31:27 CST
Severity : Informational
Type : Ethernet Monitor Event
Component : hw_node:1,hw_eth:0
Message : Node 1 eth0 Ethernet device error detected- Receive Error count increased by (2) (200%)- Receive Frame Error count increased by (2) (200%)


Top
 Profile  
Reply with quote  
 Post subject: Re: Receive Error count on management interfaces
PostPosted: Tue Jan 07, 2014 10:59 am 
Site Admin
User avatar

Joined: Tue Aug 18, 2009 10:35 pm
Posts: 1328
Location: Dallas, Texas
What type of switch are they connected to?

Generic suggestion, you might want to hard code the speed and duplex settings for the switch port.

_________________
Richard Siemers
The views and opinions expressed are my own and do not necessarily reflect those of my employer.


Top
 Profile  
Reply with quote  
 Post subject: Re: Receive Error count on management interfaces
PostPosted: Thu Jan 09, 2014 7:30 pm 
User avatar

Joined: Fri Jun 21, 2013 1:03 pm
Posts: 113
Location: USA
They are connected to a couple of 5406zl's via the 20-port gig copper modules.

Didn't see any frame alignment errors or port flapping so didn't think it was a duplex issue, but will try hard-coding the node on site.


Top
 Profile  
Reply with quote  
 Post subject: Re: Receive Error count on management interfaces
PostPosted: Fri Jan 10, 2014 12:04 pm 

Joined: Sun Jul 29, 2012 9:30 am
Posts: 576
Hmm, reminds me of the issues we had on our V400. We found back in 3.1.1 there were issues which believe it not 3par said were compatibility issues with certain Cisco switches and code level. We always called bunk on that, but the way we resolved isse was to set all the management ports to 100mb at the switch and on the array. Issues went away. I was told those port issues were fixed a while back and was getting ready to move my ports back to AUTO (1gb), but now you have be nervous ;-)


Top
 Profile  
Reply with quote  
 Post subject: Re: Receive Error count on management interfaces
PostPosted: Tue Jan 14, 2014 12:05 pm 
Site Admin
User avatar

Joined: Tue Aug 18, 2009 10:35 pm
Posts: 1328
Location: Dallas, Texas
I have similar issues on my Cisco MDS9148 SAN switch management ports connecting to Cisco NX5000 switches... Cisco can't even auto-negotiate with itself correctly at times.

_________________
Richard Siemers
The views and opinions expressed are my own and do not necessarily reflect those of my employer.


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 


Who is online

Users browsing this forum: No registered users and 45 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group | DVGFX2 by: Matt